Zoning check.
Setbacks, height, coverage, FAR.

What a zoning district allows on a lot, from setbacks and height to lot coverage and floor area ratio, and a real zoning check ArchX did for a lot in Dallas.

How do you check what zoning allows on a lot?

Confirm the lot’s zoning district and any overlays on the city’s zoning map, then read the district standards in the development code: front, side and rear setbacks, maximum height, lot coverage and, where the district sets one, the maximum floor area ratio. Apply them to the lot dimensions, note the exceptions that may apply, and list what still has to be verified on the survey, the plat and with the city.

The standards and what they mean

Most residential zoning checks come down to a few numbers:

  • Setbacks, or yards: the minimum distance from the lot lines to the building.
  • Maximum height, measured the way the code defines it.
  • Lot coverage: the share of the lot that buildings may cover.
  • Floor area ratio (FAR): the ratio of floor area to lot area. A FAR of 1.0 on a 7,500 sq ft lot allows 7,500 sq ft of floor area.

Example: Dallas R-7.5(A)

For single family structures in the R-7.5(A) district, the City of Dallas lists a 25 ft front yard, 5 ft side and rear yards, a maximum height of 30 ft, 45 % lot coverage for residential structures and a minimum lot area of 7,500 sq ft. The district sets no maximum floor area ratio, so FAR does not limit a house there; other districts may set one.

How to do it.

  1. 01

    Confirm the district

    Zoning and overlays from the city’s zoning map.

  2. 02

    Read the standards

    Setbacks, height, coverage and FAR, with the code section.

  3. 03

    Apply them to the lot

    Lot area, buildable area, maximum footprint and floor area.

  4. 04

    Check the exceptions

    Accessory buildings, yard exceptions and special approvals.

  5. 05

    List what to verify

    Survey, plat, deed restrictions and earlier decisions.

A real example: a 50 × 150 ft lot zoned R-7.5(A) in Dallas.

One question to ArchX about setbacks, height, lot coverage and a detached ADU on a residential lot: back came the district standards with the code section, the coverage worked out for the lot, the approval route for the ADU and a list of what to verify before design.

From ArchX’s answer:

  • Front setback 25 ft, side and rear setbacks 5 ft, maximum height 30 ft, residential lot coverage 45 %, cited to Dallas Development Code §51A-4.112(f)(4).
  • Lot area 50 ft × 150 ft = 7,500 sq ft; maximum covered footprint 7,500 × 45 % = 3,375 sq ft for house, garage and ADU together.
  • Detached ADU: usually a Board of Adjustment special exception, with an owner-occupancy deed restriction.
  • To verify: overlays, survey, recorded plat, deed restrictions and the existing footprints.
1 min 49 s

ArchX working time, measured

3,375 sq ft

maximum covered footprint at 45 % lot coverage

Standard U.S. test question from the blind evaluation of October 30, 2026, without project files; the lot’s street address is left out here. See all results

Asked briefly.

Does ArchX look up the zoning itself?

Yes. In another test on a lot in Dallas, ArchX read the zoning district from the city’s map and the lot size from the appraisal district’s record, then worked out the building envelope with the code sections.

Is the zoning check binding?

No. It shows what the code says and what still has to be verified. The city’s zoning review decides.

How long does it take?

In the example 1 min 49 s of ArchX working time, measured, for a written answer with the code sections.

Sources, read November 1, 2026: City of Dallas: R-7.5(A) district standards · Dallas Development Code §51A-2.102, definitions

Try it on your own work.

Download ArchX for Mac or Windows and give it a task from your firm. 7 days free with your ChatGPT account (Plus or higher).